cordn

AI Photo Booth Kiosk Setup

Everything you need to get your kiosk up and running for your event.

Your kiosk has already been configured for your event. In most cases, simply plug it in and the photo experience will launch automatically.

Quick Start

Quick and simple.

1

Assemble the Kiosk

Assemble the kiosk according to the manufacturer's assembly requirements.

2

Plug It In

Connect the kiosk to power. It should automatically power on and launch the photo booth experience.

It may take a short time for the device and photo application to completely load.

Do not begin changing settings if the experience does not appear immediately. Give the kiosk a moment to finish starting.

3

Confirm Internet Connection

Whenever possible, the kiosk will arrive with the event Wi-Fi already configured. If the photo experience loads normally, no additional setup may be required.

The AI Photo Booth requires an active internet connection to generate photos.

Conference and venue Wi-Fi can occasionally take time to connect after the kiosk starts. If the kiosk appears disconnected, give it a short period of time before changing settings.

4

Take a Test Photo

Before guests arrive, take at least one complete test photo. Confirm that:

  • The camera opens.
  • The photo can be captured.
  • AI processing begins.
  • The finished photo appears.
  • The QR code appears and can be scanned.

If all of those steps work, the kiosk is ready for the event.

5

Position the Kiosk

When you're ready for the event, position the kiosk where guests can comfortably stand approximately 3–6 feet in front of the camera.

For best results:

  • •Avoid placing the kiosk directly in front of a bright window.
  • •Make sure the area is reasonably well lit.
  • •Leave enough room for individuals and small groups.
  • •Keep the kiosk connected to power throughout the event.

Photo: Kiosk positioned and ready for guests

Running the Event, Start to Finish

Never run the booth before? This is the whole process from arrival to the last guest — the sections below go deeper on each part.

Before Guests Arrive

  1. 1Assemble the kiosk and plug it in. The photo experience launches on its own — just give it a few minutes to load (see Quick Start).
  2. 2Confirm the kiosk is online. If the event screen appears with your event's name and logo, you're connected.
  3. 3Take one complete test photo yourself, all the way through to the finished picture and QR code (see Take a Test Photo).
  4. 4Position the kiosk with the screen in landscape (horizontal) orientation, out of direct sun, with room for guests to stand 3–6 feet back.

What Each Guest Does

The booth guides guests on its own — your job is mostly to keep it powered and online.

  1. 1Guest taps Start on the event's welcome screen and picks a photo experience (some events also offer a View Live Gallery button here).
  2. 2The guest follows the on-screen prompts and the photo is captured.
  3. 3The AI transforms the photo — this takes a little while and shows a progress screen.
  4. 4The finished picture appears. Tapping it shows it full size; tapping outside closes that view.
  5. 5The guest fills in the Get Your Photo form and taps Send to Me — the photo is emailed and a QR code pops up on screen to scan and download it instantly. Events with a Get QR Code button skip the form instead.
  6. 6The guest can tap Try Another Persona for a new version from the same picture, or Post to Gallery to put it on the event's gallery screen (see After Your Photo).
  7. 7Tapping Start Over returns to the welcome screen, ready for the next guest.

Button names can differ slightly per event, but every event follows this same flow.

During the Event

  • •Keep the kiosk on power and online the whole time — that's what photos need to generate.
  • •Photos guests post appear on the live gallery screen automatically (see Live Gallery).
  • •If anything stops working, work through Common Issues — most fixes take under a minute.
  • •Still stuck? cordn support contact details are at the bottom of this page.

Need to Connect to Wi-Fi?

If Wi-Fi was not preconfigured, or the venue network has changed, follow these steps.

1

From inside the photo booth experience, swipe inward from the LEFT edge of the screen. This opens the Fully Kiosk menu.

Screenshot: Swipe from left side to open Fully Kiosk menu

2

Select Exit Fully. This temporarily exits the kiosk application.

Screenshot: Fully Kiosk menu showing Exit Fully

3

Once you are back on the kiosk home screen, tap the Settings icon in the upper-right corner.

4

Open Network Settings, then select the appropriate Wi-Fi network and enter the password if required.

Conference Wi-Fi can be slow to appear.

  • •Stay on the Network Settings screen for a moment.
  • •Allow the kiosk time to scan again.
  • •Wait for the Wi-Fi network to reappear.
  • •Select the network once it becomes available.

Do not repeatedly restart the kiosk simply because the Wi-Fi network takes a moment to appear.

If the venue uses a Wi-Fi login page or captive portal, follow the venue's normal login process.

5

Once Wi-Fi is connected, return to the kiosk home screen and reopen Fully Kiosk Browser. Fully Kiosk should automatically reopen the event's photo booth experience.

Screenshot: Fully Kiosk icon on kiosk home screen

Camera Says "Not Connected"?

Occasionally when the kiosk first starts, the external camera may not initialize correctly. This is usually very easy to fix.

The Fix

  1. 1Tap Back in the upper-left corner of the photo experience until you return to the main kiosk screen.
  2. 2Go to the back of the kiosk.
  3. 3Locate the camera USB connection.
  4. 4Unplug the camera USB cable.
  5. 5Wait a few seconds.
  6. 6Plug the camera USB cable back into the same USB port.
  7. 7Return to the photo experience.
  8. 8Try taking another photo.

Screenshot: Back button in upper-left corner

Photo: Location of camera USB connection on rear of kiosk

You normally do NOT need to restart the entire kiosk for this issue. Reconnecting the camera USB cable usually resolves it.

Using the Photo Booth

Starting a Photo

From the main photo booth screen:

You do not need to be inside the circle on the capture screen. Anyone in the camera's view may end up in the photo, so be cautious of who is in the background.

  1. 1Select the desired photo experience.
  2. 2Follow the prompts on screen.
  3. 3Position yourself in front of the camera.
  4. 4Capture the photo.
  5. 5Wait while the AI image is created.
  6. 6View the finished image.
  7. 7Scan the QR code to receive the photo.
  8. 8Start another session when ready.

AI photo generation requires internet access. Processing time may vary depending on venue internet quality.

After Your Photo

Once the AI photo is finished, guests have several options on the result screen. Your event may use slightly different button names.

Getting the Photo (Send to Me / Get QR Code)

  • •The Get Your Photo form collects the guest's details. After filling it in, tapping Send to Me emails the photo to the guest.
  • •As soon as the photo is sent, a QR code pops up on screen. The guest can scan it with their phone camera to download and share the photo right away.
  • •If the event shows a Get QR Code button, tapping it skips the form and brings up the QR code immediately.

Screenshot: QR code screen after Send to Me

Try Another Persona

Try Another Persona creates a brand-new AI photo from the same original picture with a different character or style — no new photo needed. Anything the guest already typed into the form carries over, so they don't have to enter it again.

Guests can keep tapping it to cycle through the event's personas. The finished photo replaces the one on screen, and a new QR code is produced after sending.

Post to Gallery

Post to Gallery puts the photo on the event's live gallery screen for everyone to see. A "Posted!" confirmation appears once it's on the wall.

Start Over

Start Over returns to the main kiosk screen so the next guest can begin a fresh photo. The previous picture stays safe — it has already been delivered or posted by then.

Viewing the Finished Photo

On the result screen, tap the photo to view it full size. Tap the ✕ in the corner — or anywhere outside the photo — to close it.

Need to Go Back?

When available, use the Back button in the upper-left corner of the screen to return to the previous page.

Screenshot: Back button

Returning to the main booth page is useful when:

  • •A guest wants to restart.
  • •The camera needs to be reconnected.
  • •Someone accidentally enters the wrong experience.
  • •You need to return to the event home screen.

Common Issues

Please Don't Change These Settings

  • ✕Factory reset the kiosk.
  • ✕Remove Fully Kiosk Browser.
  • ✕Change Fully Kiosk configuration.
  • ✕Change camera permissions.
  • ✕Install Android system updates during the event.
  • ✕Remove the configured photo booth application.
  • ✕Change browser settings.
  • ✕Move the camera USB cable to another port unless instructed.

The kiosk has been configured specifically for your event.

Need Help During Your Event?

If the steps above do not resolve the issue, contact cordn support.

When contacting support, please send:

  • •Your event name
  • •A brief description of what is happening
  • •A photo of the kiosk screen if possible
Contact Support
cordn AI Photo Booth